1
R&S® RT-ZP passive probe series
Passive voltage probes (38 MHz to 700 MHz, 1:1 / 10:1 attenuation)
- Category: Oscilloscope probe
- Manufacturer: Rohde & Schwarz
- Maximum bandwidth: 700 MHz (RT-ZP11, RT-ZPMMCX)
- Attenuation ratio: 1:1, 10:1, 25:1, 100:1 (by model)
- Input impedance: 1 MΩ ∥ 39 pF up to 100 MΩ ∥ 4.6 pF (by model)
- Maximum measurable voltage: up to 3540 V RMS (CAT 0, RT-ZI11)
- Safety category: CAT 0 / CAT II / CAT III / CAT IV (by model)
- Probe connection: Standard probe tip / MMCX (RT-ZPMMCX)
- Compatible oscilloscopes: RTO2000, RTE1000, RTM3000, RTB2000, MXO 3/4/5, RTH handheld (by model)
- Probe tip material: 0.5 mm gold-plated spring tip (RT-ZP11)
- CAT IV rated voltage: 600 V RMS (RT-ZI10)
- Bandwidth in 1:1 mode: 38 MHz (RT-ZP1X)
- MMCX attenuation: 25:1, up to 30 V RMS, 14.9 MΩ ∥ <4 pF (RT-ZPMMCX)
- Operating temperature: −40 °C to +155 °C (some accessories)
- Data sheet: Download PDF
- Product brochure: Download PDF
- External link: Official product page
Overview
The R&S® RT-ZP passive probes are the all-rounders for general purpose oscilloscope work, spanning 38 MHz to 700 MHz and everything from routine circuit debugging to high-voltage measurement in the field. The series offers 1:1, 10:1, 25:1 and 100:1 attenuation ratios and safety categories from CAT 0 to CAT IV, reaching up to 3540 V RMS where the electrical environment demands it. Each model is matched to the mainstream Rohde & Schwarz oscilloscope platforms — RTO2000, MXO 3/4/5, RTH and others — and the broad RT-ZA accessory range makes contact at almost any test point, which is what shortens design verification and fault-finding in practice.
Key features
- Bandwidth up to 700 MHz (RT-ZP11 and RT-ZPMMCX) for high-speed digital and RF circuits
- A choice of attenuation ratios (1:1, 10:1, 25:1, 100:1) covering low-voltage signals through to very high voltages
- Safety categories CAT 0 to CAT IV and up to 3540 V RMS, to meet strict site safety requirements
- The RT-ZP11 carries a 0.5 mm gold-plated spring tip for steady mechanical contact and low contact resistance
- The RT-ZPMMCX uses an MMCX connection, designed for the compact MXO 4 and MXO 5 oscilloscopes
- The RT-ZP10 is pre-compensated at the factory for the best frequency response on the RTO2000 / RTE1000 platform
- The RT-ZI10 / RT-ZI11 are isolated passive probes, available in two- and four-probe bundles for multichannel work
- A broad RT-ZA accessory range (spring clips, micro clips, lead sets, PCB adapters) reaches any test point
- The RT-ZI10C and RT-ZI11 are designed for the RTH handheld oscilloscopes, for measurement in the field
Typical applications
- Board design verification and functional debugging (digital timing, analog signal integrity)
- Power supply and power electronics design (high-voltage switching nodes, motor drive circuits)
- Field service and preventive maintenance on industrial equipment (high-voltage CAT IV environments)
- Embedded development and MCU/FPGA interface analysis
- RF and high-speed digital prototype verification (where 500 MHz to 700 MHz probe bandwidth is needed)
- Teaching and general laboratory measurement (cost-effective entry-level passive probes)
Configure your R&S® RT-ZP Passive Probe Series
Pick a base model and its options, watch your order list build as you go, then send it for a quote in one click. Every order number (Order No.) comes from Rohde & Schwarz factory data.
2
Probes
9 options
3
Accessories
18 optionsAvailable models / variants
The series comprises the 9 variants below. Click "Request a quote" for full specifications and pricing on a given model from KanTek.
| Model | Differences | |
|---|---|---|
| RT-ZP1X (1333.1370.02) | Request a quote → | |
| RT-ZP03S (1803.1001.02) | Request a quote → | |
| RT-ZP05S (1333.2401.02) | Request a quote → | |
| RT-ZP10 (1409.7550.00) | Request a quote → | |
| RT-ZP11 (1803.0005.02) | Request a quote → | |
| RT-ZI10 (1326.1761.02) | Request a quote → | |
| RT-ZI10C (1326.3106.02) | Request a quote → | |
| RT-ZI11 (1326.1810.02) | Request a quote → | |
| RT-ZPMMCX (1803.1599.02) | Request a quote → |
Frequently asked questions
Yes. KanTek Technology is the authorized Taiwan distributor for Rohde & Schwarz, supplying new R&S® RT-ZP Passive Probe Series instruments with factory quotations and technical advice.
Instrument rental is launching soon. R&S® RT-ZP Passive Probe Series is part of the line-up being prepared, and advance enquiries are welcome.
Yes. KanTek provides calibration and repair for R&S® RT-ZP Passive Probe Series, with calibration performed by a partner laboratory, to keep the instrument accurate and available.
Use Request a quote on this page, or call +886-2-2999-7719. KanTek replies within 24 hours with pricing, lead time and the options that suit your application.
R&S® RT-ZP Passive Probe Series is a Rohde & Schwarz product: Passive voltage probe family (38 MHz to 700 MHz, 1:1 / 10:1 attenuation). Contact KanTek for selection or application advice.
Authorized R&S distributor
Repair and calibration services
Instrument rental, launching soon
Reply within 24 hours
Need R&S® RT-ZP Passive Probe Series pricing, rental or calibration?