1
R&S®CMPHEAD50
mmWave remote radio head (21.84 – 50.20 GHz, for the CMP200)
- Category: Wireless device test system
- Manufacturer: Rohde & Schwarz
- Frequency range: 21.84 GHz to 50.20 GHz
- Frequency resolution: < 0.1 Hz
- RF output power: Up to +25 dBm
- Output level resolution: 0.1 dB
- EVM (5G NR FR2 signal): As good as -46 dB / 0.5%
- Supported bands: All 3GPP FR2-1 bands (five mmWave bands)
- Test direction: Bidirectional (TX / RX)
- Local oscillator: Separate LO for TX and RX (dual LO)
- External LO input ports: Separate external LO input for TX and for RX
- RF switch matrix: Integrated mmWave RF switch matrix
- Low-noise RX port: Extra sensitive low-noise RX port (HDR mode)
- Order number (base model): 1201.0002K26.base
- Data sheet: Download PDF
- Product brochure: Download PDF
- External link: Official product page
Product overview
The R&S®CMPHEAD50 is the next generation broadband mmWave remote radio head, a high-performance millimeterwave converter designed for non-signaling applications. It is the only remote radio head on the market that covers bidirectional testing of five mmWave bands with a single hardware combination, and it adds EVM booster ports. Used with the CMP200 radio communication tester, it extends test coverage into frequency range 2 (FR2 / FR2-1). A wider dynamic range, full frequency coverage and outstanding EVM performance keep measurement accuracy high for next-generation FR2 RF designs, from early development through to final certification and regulatory compliance testing.
Key features
- Full frequency range from 21.84 GHz to 50.2 GHz: the only remote radio head on the market that covers every 3GPP FR2-1 band and at the same time offers separate external LO inputs for TX and RX
- Wide dynamic range with an extra sensitive RX port: the standard TX/RX ports already deliver excellent EVM performance, and the added low-noise RX port raises sensitivity to a new level for very low power measurements
- Dual LO architecture with external LO ports: separate local oscillators for the downlink and uplink paths give the best RF signal quality in both the TX and the RX direction
- External LO ports support the EVM booster, which improves EVM performance further for leading-edge RF measurements
- Integrated mmWave RF switch matrix simplifies the system setup and supports switching between bands
- One hardware combination covers bidirectional testing of five mmWave bands, cutting test cost and system complexity
Typical applications
- Non-signaling RF testing of 5G NR FR2 / FR2-1 user equipment (UE)
- Early development validation of next-generation mmWave RF designs
- Final certification and regulatory compliance testing
- High dynamic range millimeterwave receive sensitivity measurements
- Verification of 5G millimeterwave multi-band switching performance
Configure your R&S®CMPHEAD50
Pick a base model and its options, watch your order list build as you go, then send it for a quote in one click. Every order number (Order No.) comes from Rohde & Schwarz factory data.
Available models / variants
This series comes in the 1 variant below. Click "Request a quote" to ask KanTek Technology for the full specification and pricing of that model.
| Model code | Specification difference | |
|---|---|---|
| 1201.0002K26.base | R&S®CMPHEAD50 base model with five mmWave bands, bidirectional testing, dual LO and a low-noise RX port | Request a quote → |
Frequently asked questions
Yes. KanTek Technology is the authorized Taiwan distributor for Rohde & Schwarz, supplying new R&S®CMPHEAD50 instruments with factory quotations and technical advice.
Instrument rental is launching soon. R&S®CMPHEAD50 is part of the line-up being prepared, and advance enquiries are welcome.
Yes. KanTek provides calibration and repair for R&S®CMPHEAD50, with calibration performed by a partner laboratory, to keep the instrument accurate and available.
Use Request a quote on this page, or call +886-2-2999-7719. KanTek replies within 24 hours with pricing, lead time and the options that suit your application.
R&S®CMPHEAD50 is a Rohde & Schwarz product: mmWave remote radio head (21.84 – 50.20 GHz, for the CMP200). Contact KanTek for selection or application advice.
Authorized R&S distributor
Repair and calibration services
Instrument rental, launching soon
Reply within 24 hours
Need R&S®CMPHEAD50 pricing, rental or calibration?